Source: Reproduced with permission from Chen [51]. Copyright 2018, Elsevier.
Bacterial cellulose (BC) has been widely used due to outstanding advantages such as high elastic modulus, good degree of polymerization, and biocompatibility. Kim et al. used bacterial nanocellulose film as the triboelectric material in the TENG. The bacteria can generate the BC pellicle in a gel state. The uniform BC film was prepared by dissolving the BC pellicle at a specified concentration [52]. CNFs generated from nanosized cellulose fibrils are proverbially used in modern electronic devices due to their desirable surface roughness and electrical properties. Yao et al. produced biodegradable CNF films with nanostructured surface and applied them in the TENG [53]. The CNF hydrogel was produced into a CNF film by a treating process, where wood pulp was oxidized and then mechanically homogenized. By filtering and the drying processes, the CNF hydrogel can be transformed to transparent and flexible CNF thin films. When contacted with the FEP film, the surface of the CNF film could hold positive triboelectric charges due to its very positive position on the triboelectric series. Single cellulose films are fragile and volatile. To conquer these problems, Chandrasekhar et al. developed a cellulose/polydimethylsiloxane (PDMS) film in the TENG [54]. Composite films with irregular surface roughness were fabricated by solidifying the mixed solution of cellulose powders and PDMS on the sandpaper template. The content of cellulose could affect the output performance of the TENG. Peng et al. fabricated the composite film with PDMS and CNC flakes and found that the cellulose can increase the output performance of the TENG due to the favorable dielectric property [55].
One drawback of natural CNFs is the weak polarization, resulting in low capability to generate surface charges. Introducing different chemical groups to the CNFs could increase the capability. Yao et al. fabricated the CNF film by filtering the hydrogel and then drying, and modified the film by a nitration acid mixture of HNO3, H2SO4, and water [56]. Compared to the pristine CNFs in the corresponding Fourier transform infrared spectroscopy (FTIR) curves, the nitro‐CNFs possessed three new intense peaks due to asymmetric and symmetric stretching of the NO2 group and stretching of the NO bonds. The output voltage signals of the pristine CNF–Cu pair were about 0.8 V and of the nitro‐CNF–Cu pair were about 4.9 V, in the TENGs. Nanostructures on triboelectric materials can increase contacting areas, leading to increased electrostatic charges on these surfaces. Šutka et al. developed highly porous ethyl cellulose (EC) nanostructured films for the TENG [57]. The porous EC films were fabricated by phase inversion of the mixed solution (ethyl cellulose, ethanol, and toluene). The output voltage signals of the TENG based on porous EC films are higher than that of the TENG based on primary EC films. He et al. developed 1D cellulose nanofibers into the pores of cellulose microfibers skeleton, leading to the fabrication of a nanostructured paper, which can be used as template to carry other materials [58].
To boost the electron‐donating tendency of cellulose, Oh et al. fabricated highly conductive ferroelectric cellulose composite papers, which consist of cellulose, silver nanowires, and BaTiO3 nanoparticles [59]. The composite papers were produced through a simple filtration method, with the thickness of the prepared paper of about 70 μm, and were used in the TENG, resulting in high output performances. With the rapid development of printing technique, some researchers explored new methods to fabricate surfaces with micro/nanostructure. Qian et al. developed a biocompatible cellulose‐based TENG through the all‐printing method. The 3D patterned positive layer could be fabricated by printing the CNF ink onto the Ag/PET substrates [60].
2.3.2.2 Metal
Metallic materials, such as copper (Cu) foils, aluminum (Al) foils, and silver (Ag) foils, have been widely used as electrodes of TENGs, which can export the charges generated by the coupling of triboelectric friction and electrostatic induction. Al foils can be used as both a triboelectric layer and an electrode in the TENG due to the high electrical conductivity and the positive position on the triboelectric series. The surface of the Al foil would form positive charges, when it makes contact with the other film with the negative position. Superhydrophobic surfaces emerging from the cooperation of low surface energy and micro/nanostructures are widely explored in biological systems. To increase the surface roughness and environmental stability of the metallic electrodes, Zhao et al. fabricated a superhydrophobic surface on the Al substrates by using chemical etching method [61]. Al substrates were firstly polished to eliminate the dense oxidation on the Al substrates. The polished surface is smooth, as shown in Figure 2.7a,b. The contact angle on the surface is about 62°, as illustrated in Figure 2.7c. After chemical etching, nanostructures are fabricated on the Al substrates, as shown in Figure 2.7d. High magnification SEM of the etched Al substrate shows that protruding structures were formed on the substrate (Figure 2.7e). The contact angle on the etched Al substrate is about 33°, due to the cooperation of the hydrophilic property of Al and the nanostructures.
By modifying with 1H,1H,2H,2H‐perfluorodecyltrichlorosilane/toluene solution, the surface energy of the etched Al substrate could be decreased, leading to the formation of a superhydrophobic surface on the Al substrate. Figure 2.7i shows that the contact angle on the prepared superhydrophobic surface is about 153°. Figure 2.7j shows the values for three different surfaces. Figure 2.7k shows a photograph of water drops with different sizes on the superhydrophobic surface. It is found that the superhydrophobic surface could form positive charges when it made contact with a polyamide film in the TENG.
2.3.2.3 Polymer
Polymers, such as PTFE, FEP, and PDMS, are ideal triboelectric materials for TENGs due to the flexibility and the excellent dielectric property. The surface roughness and environmental stability of the polymers in the TENGs can be enhanced with many advanced methods, such as plasma (ICP)‐reactive ion etching, template method, and 3D printed method. PDMS possesses a great deal of advantages, such as flexibility, transparency, and high electronegativity, and can be easily produced in special shapes. To study the influence of the surface morphology for the TENG, Dudem et al. developed functional polydimethylsiloxane (NpA‐PDMS) layers by soft imprint lithography [62]. The prepared layers possessed nanopillar‐like architectures, which could be used to increase the output voltage of the TENG.
PTFE is a common negative triboelectric material, exhibiting strong electron‐attracting ability and excellent flexibility. Guo et al. utilized inductively coupled plasma (ICP) ion etching to produce nanostructures on the PTFE film [63]. The fabricated PTFE film could form more charges when it made contact with the electrode, resulting in high output performance of the TENG. Wang et al. fabricated sponge‐like porous PTFE thin films by using deionized (DI) water as the soft template [64]. Compared with that based on flat PTFE film, the output performance based on porous PTFE thin film was obviously enhanced. Zhao et al. fabricated polytetrafluoroethylene/polyethene oxide (PTFE/PEO) membranes by using electrospinning method. In order to further enhance the charge density on the composite membranes, they introduced a high amount of stable static negative charges on the surface of the membranes [65].
Figure 2.7 Superhydrophobic surfaces on the Al substrates. (a) SEM image of the polished Al substrate. (b) High magnification SEM image of the polished Al substrate. (c) Image of the contact angle of water on the polished Al substrate. (d) SEM image of the etched Al substrate. (e) High‐magnification SEM image of the