The old method of topping out a low board fence is shown at figure 38. Since barbed wire has become plenty, it is more usual to increase the height of the fence by stringing one or two strands of that on vertical slats nailed to the tops of the posts. Yet, in cases where there are plenty of sound rails left from some old fence, or plenty of straight saplings, the old method is still a very cheap and convenient one.
CHAPTER IV.
PICKET FENCES.
A GOOD GARDEN FENCE.
Fig. 39.—A Lath And Picket Fence.
The engraving, figure 39, represents a good, substantial garden fence, that, while somewhat more serviceable than the ordinary kind, may be constructed at less cost. It does not materially differ from the common picket fence, further than that the pickets are put five inches apart, with strips of lath nailed between. The pickets give the necessary strength, while the lath, as a shield against poultry, or rabbits and other vermin, is equally as good at one-sixth the cost. An old picket fence surrounding a garden or yard, may be “lathed” in the manner here indicated at little expense.
A SOUTHERN PICKET FENCE.
Fig. 40.—Southern Picket Fence.
Fig. 41.—Bench For Sawing Pickets.
The picket fence in very general use in the Southern States, is shown in figure 40. It will be observed that the pickets, instead of terminating in an equal-sided point, have but one slanting side, while the other is straight. Such a fence looks quite as well as one with the other style of points, and is exceedingly neat and serviceable along the line of the street, or to mark the boundary between two estates. To facilitate the sawing of the pickets, the bench or horse represented in figure 41 is employed. This has a stop at one end, while near the other end are two upright pieces to serve as guides in sawing. The edge of one of these is far enough in the rear of the other to give the desired slope. In sawing, the saw rests against these guides, as shown by the dotted lines. In a picket fence, the point where decay commences, is where the pickets cross the string pieces. Water enters between the two, and decay takes place which is unsuspected until the breaking of a picket reveals the state of affairs. The string pieces and the pickets, at least upon one side, should be painted before putting them together, and nailed while the paint is fresh.
FENCES OF SPLIT PICKETS.
Fig. 42.—A Fence Of Split Stuff.
Fig. 43.—Cheap Fence Of Split Timber.
In localities where sawed timber is expensive, and split timber is readily obtained, a very neat picket fence may be made with very little outlay, by using round posts, split stringers, and rived pickets, as shown in the engraving, figure 42. The stringers are eight to twelve feet in length, and usually one of the flat sides is sufficiently smooth for receiving the pickets. Let the stringers project a few inches beyond each post, adding strength to the fence, and should the posts decay, new ones may be driven in on either side, and the stringers readily attached by heavy nails or spikes. With timber that splits freely, a man can rive out five or six hundred pickets in a day. The construction of the fence is plainly shown in the above engraving.
Figure 43 represents a fence made entirely of split timber, the only cash outlay being for nails. This may be made so as to turn, not only all kinds of stock, but rabbits, etc. The pickets are sharpened, and driven six or eight inches into the ground, and firmly nailed to a strong string-piece at top.
Fig. 44.—Common Picket Fence.
Another good substantial fence is represented by figure 44, which, though somewhat expensive, is especially adapted for yard, orchard and vineyard enclosure. This needs no explanation. The posts should not be set further than eight feet apart; two by four-inch scantlings should be used to nail to, and split palings should be nailed on with annealed steel nails.
ORNAMENTAL PICKET FENCES.
Fig. 45.—Ornamental Picket Fence.
Fig. 46.
The fence shown in figure 45 may be constructed with flat pickets, three inches wide and three feet five inches long. The notches in the pickets are easily made with a compass saw, or a foot-power scroll-saw. The top and bottom pieces between the pickets may be painted some other color than the fence, if so desired. Any carpenter should be able to construct it at a small advance over a fence made from plain pickets, making the pattern as in figure 46.
A plainer, but still very neat form of picket fence is illustrated at figure 47. The intermediate pieces are notched at one end and square at the other.
Fig. 47.—A Plainer Picket Fence.
RUSTIC PICKET FENCES.
Fig. 48.—Rustic Sapling Fence.
Fig. 49.—Rustic Picket Fence.
When the farmers on the prairies prevent the spreading of the prairie fires, young oak and hickory saplings spring up as if by magic near all the wooded streams. These saplings come from huge roots whose tops have yearly been destroyed by fire. In that section farmers often construct a very neat rustic fence from two or three year old saplings, having the appearance of figure 48. The rustic pickets are trimmed so as to leave the branches projecting about two inches, and are nailed on with four-penny nails. A fence of this kind would not last long, unless the pickets, posts, and rails were free of bark,