Figure 1.6 Largest commercially available wind turbines.
Hence, over the last 25 years there has been a continuous increase in the rotor diameter of commercially available wind turbines from around 40 m to several manufacturers offering turbines of more than 170 m (Figure 1.6). A tripling of the rotor diameter leads to a nine times increase in power output. The influence of the wind speed is even more pronounced, with a doubling of wind speed leading to an eightfold increase in power. Thus, there have been considerable efforts to ensure that wind farms are developed in areas of the highest wind speeds and the turbines optimally located within wind farms. In certain countries, with modest wind speeds, very high towers are being used to take advantage of the increase of wind speed with height.
In the past a number of studies were undertaken to determine the optimum size of a wind turbine by balancing the complete costs of manufacture, installation, and operation of various sizes of wind turbines against the revenue generated (Molly et al. 1993). However, these early estimates would now appear to be too low, and more recent studies indicate that the lowest cost of energy is obtained with rotors approaching 150 m diameter, although smaller turbines may be preferred on some sites for reasons of environmental impact and difficulty of transporting very large components to the site. Even larger turbines give the lowest cost of energy offshore, where the foundation and cabling costs of individual turbine are high and the very large blades can be transported by ship directly from the factory to the site.
All modern electricity generating wind turbines use the lift force derived from the blades to drive the rotor. A high rotational speed of the rotor is desirable to reduce the gearbox ratio required, and this leads to a low solidity rotor (the ratio of blade area to rotor swept area). The low solidity rotor acts as an effective energy concentrator, and as a result the energy generated over a wind turbine's life is much greater than that used for its manufacture and installation. An energy balance analysis of a 3 MW wind turbine showed that the expected average time to generate a similar quantity of energy to that used for its manufacture, operation, transport, dismantling, and disposal was six to seven months (European Wind Energy Association 2009). A similar time was calculated for offshore wind turbines. Offshore the higher mean wind speeds, and hence greater energy output, compensate for the higher wind farm costs and energy expended in construction and operation.
Until around the year 2000, the installed wind turbine generating capacity was so low that its output was viewed by electricity Transmission System Operators simply as negative load that supplied energy but played no part in the operation of the power system and maintaining its stability. Since then, with the greatly increased capacity of wind generation, turbines are required to contribute to the operation of the power system. The requirements for their performance are defined through the Grid Codes, issued by the Transmission System Operators (Roberts 2018). Compliance is mandatory and must be demonstrated before connection to the network is allowed. Compliance with the Grid Code requirements is difficult to achieve with simple fixed speed induction generators using the Danish concept, and these regulations have been a major driver for the use of variable‐speed generators.
1.3 Scope of the book
The use of wind energy to generate electricity is now well accepted, with a large industry manufacturing and installing up to 50 GW of new capacity each year. Although there are exciting new developments, particularly in very large offshore turbines, and many challenges remain, there is a considerable body of established knowledge concerning the science and technology of wind turbines. This book records some of this knowledge and presents it in a form suitable for use by students (at final year undergraduate or post‐graduate level) and by those involved in the design, manufacture, or operation of wind turbines. The overwhelming majority of wind turbines presently in use are horizontal axis connected to a large electricity network. These turbines are the subject of this book.
Chapter 2 discusses the wind resource. Particular reference is made to wind turbulence due to its importance in wind turbine design. Chapter 3 sets out the basis of the aerodynamics of horizontal axis wind turbines, while Chapter 4 discusses more specialised aspects of wind turbine aerodynamics. Any wind turbine design starts with establishing the design loads, and these are discussed in Chapter 5. Chapter 6 sets out the various design options for horizontal axis wind turbines, with approaches to the design of some of the important components examined in Chapter 7. The functions of the wind turbine controller and some of the possible techniques used to design and implement the controllers are discussed in Chapter 8. Wake effects and wind farm control are discussed in Chapter 9. This is a new chapter in this edition. In Chapter 10, wind farms and the development of wind energy projects are reviewed, with particular emphasis on environmental impact. Chapter 11 considers how wind turbines are connected to electrical networks and their characteristics as an increasingly important source of generation. Very large wind farms with multi‐megawatt turbines are now being constructed many kilometres offshore, and a considerably expanded Chapter 12 deals with the important topic of offshore wind energy.
The book attempts to record well‐established knowledge that is relevant to wind turbines that are currently commercially significant. Thus, it does not discuss a number of interesting research topics or areas where wind turbine technology is still evolving. Although they were investigated in considerable detail in the 1980s, large vertical axis wind turbines have not proved to be commercially competitive and are not currently manufactured in significant numbers. Hence, the particular issues of vertical axis turbines are not dealt with in this text.
There are presently around one billion people in the world without access to reliable mains electricity, and, in conjunction with other generators (e.g. batteries, diesel engines, and solar photovoltaic units), wind turbines may in the future be an effective means of providing some of them with power. However, autonomous power systems (sometimes known as autonomous microgrids) are extremely difficult to operate reliably, particularly in remote areas of the world and with limited budgets. A small autonomous microgrid has all the technical challenges of a large national electricity system but, due to the low inertia of the generators, requires a very fast, sophisticated control system to maintain stable operation as well as a store of energy. Over the last 40 years there have been a number of attempts to operate