Internal Combustion Engines. Allan T. Kirkpatrick

indicated work of an engine is the net work done by the gas during a compression and expansion cycle. It is equal to the integral of the pressure over the cylinder volume:

      (1.8)

      The engine power is the rate at which work is done by the engine, and for an engine with cylinders is

      since the four‐stroke engine has two revolutions per power stroke and the two‐stroke engine has one revolution per power stroke.

      The brake power is the power output of the engine measured by a dynamometer. Early dynamometers were simple brake mechanisms, hence the use of the term . The engine torque, , is a measure of the work done per unit rotation (radians) of the crank. As we shall see when discussing dynamometers in Chapter 12, the brake power and torque for both two‐ and four‐stroke engines are related by

      (1.11)

      The net brake power is from the complete engine; whereas gross brake power is from an engine without the cooling fan, muffler, and tail pipe. The brake power is less than the indicated power due to engine mechanical friction, pumping losses in the intake and exhaust, and accessory power needs, which are grouped as a friction power loss, :

      (1.12)

      The ratio of the brake power to the indicated power is the mechanical efficiency, :

      (1.13)

The wide open throttle performance of a 2.0 L automotive four‐stroke engine is plotted in Figure 1.7. As with most engines, the torque and power both exhibit maxima with engine speed. Viscous friction effects increase quadratically with engine speed, causing the torque curve to decrease at high engine speeds. The maximum torque occurs at lower speed than maximum power, since power is the product of torque and speed. Notice that the torque curve is rippled. This is due to both inlet and exhaust airflow dynamics and mechanical friction, discussed later.

Figure 1.7 Wide‐open throttle (WOT) performance of an automotive four‐stroke engine.

      Mean Effective Pressure

The mean effective pressure (mep), defined in Equation (1.14), is the work done per unit displacement volume. It is the average pressure that results in the same amount of work actually produced by the engine and has units of force/area. The mean effective pressure is a very useful parameter as it scales out the effect of engine size, allowing performance comparison of engines of different displacement.

(1.14)

      There are three useful mean effective pressure parameters – imep, bmep, and fmep. The indicated mean effective pressure (imep) is the net work per unit displacement volume done by the gas during compression and expansion. The name originates from the use of an 'indicator' card used in the past to plot measured pressure versus volume. The pressure in the cylinder initially increases during the expansion stroke due to the heat addition from the fuel, and then decreases due to the increase in cylinder volume.

The brake mean effective pressure (bmep) is the external shaft work per unit volume done by the engine. The name originates from the brake dynamometer used to measure the torque produced by the rotating shaft. Typical values of bmep for vehicular engines depend on the load. A low‐load bmep is about 5 bar, a mid‐load bmep is about 10 bar, and a high‐load bmep is about 20 bar. Use of turbo‐ or supercharging is generally required to produce a high‐load bmep.

      Based on torque, the bmep is

      (1.15)

      and in terms of power, the bmep is

      (1.16)

      The bmep can also be expressed in terms of piston area , mean piston speed , and number of cylinders :

      (1.17)

      The friction mean effective pressure (fmep) includes the mechanical engine friction, the pumping losses during the intake and exhaust strokes, and the work to run auxiliary components such as oil and water pumps. Accordingly, the friction mean effective pressure (fmep) is the difference between the imep and the bmep. Determination of the fmep is discussed further in Chapter 10.

      (1.18)

The bmep of two different displacement naturally aspirated automobile engines at wide‐open throttle (WOT) is compared versus mean piston speed in Figure 1.8. Notice that when performance is scaled to be size independent, there is considerable similarity.

Figure 1.8 Brake mean effective pressure at WOT versus mean piston speed for two automotive engines.

      Volumetric Efficiency

A performance parameter of importance for four‐stroke engines is the volumetric efficiency, . It is defined as the mass of air inducted into the cylinder at bottom dead center divided by the mass that would occupy the cylinder volume Скачать книгу