The Seebeck coefficient of conducting polymers is also related to the doping form. There are two types of doping forms for p‐type conducting polymers [6, 7]. Taking away electrons from the conjugated backbone is the oxidative doping. Oxidative doping is the main doping form for conjugated polymers such as polyacetylene and polythiophene. The oxidative doping can be de‐doped by reducing chemical agents. Another doping form is the protonic acid doping. It is the main doping form for polyaniline because polyaniline has ammine group [8]. Protonic acid doping was observed for polypyrrole and polythiophene as well [6, 7]. The protonic acid doping can be de‐doped by base. Yao et al. found that de‐doping the protonic acid doping by base is more effective in increasing the Seebeck coefficient than de‐doping the oxidative doping [3]. As shown in Figure 1.7, poly(3,4‐ethylenedioxythiophene):trifluoromethanesulfonate (PEDOT:OTf) can be de‐doped with reducing agents including glucose and ascorbic acid or NaOH. When PEDOT:PSS:OTf is de‐doped to the same doping level, the conductivity using glucose or ascorbic acid is similar with NaOH. But the latter can give rise to a higher Seebeck coefficient and thus the power factor than the former. This difference is ascribed to the different electronic structures by oxidative doping and protonic acid doping. The protonic acid doping takes place by attaching a proton to an α or β site of the thiophene ring of PEDOT. This distorts the conjugated structure and leads to more electrons near the Fermi level. Instead, the oxidative doping does not affect the conjugated structure. Thus, the removal of the protonic acid doping can more effectively increase the mean energy (E J) of the charge carriers and thus increase the Seebeck coefficient more remarkably.
Figure 1.6 Dependences of the electrical conductivity, Seebeck coefficient, and power factor of PEDOT:Tso on the doping level. Oxidation level is used for the doping level, and α is used for the Seebeck coefficient.
Source: Bubnova et al. [5]. © Springer Nature.
The dependence of the Seebeck coefficient on the |E J − E F| values is often used to understand the energy filtering. Energy filtering is often observed when an electronic material like nano‐fillers is mixed into a conducting polymer with different Fermi levels [9–11]. The different Fermi levels of the matrix and nano‐fillers can induce the charge transfer and an internal electric field at the interface between them. This internal electric field at the interface can block the accumulation of the charge carriers with low energy and thus increase the mean energy (E J) of the accumulated charge carriers under temperature gradient. Apart from composites of conducting polymers, energy filtering was reported when a certain material is coated on a conducting polymer film [12–14].
Figure 1.7 (a) Conductivity, (b) Seebeck coefficient, and (c) power factor of PEDOT:OTf films as a function of doping levels. NaOH, glucose, and ascorbic acid were used to de‐dope PEDOT:OTf.
Source: Yao et al. [7]. © Royal Society of Chemistry.
1.1.3 Peltier Effect
Electrical current is generated at the presence of temperature gradient in terms of the Seebeck effect. There is a reverse process to take away heat by applying an electrical current to a thermoelectric material. This is called the Peltier effect. When a charge carrier transports from the cold side to the hot side, it will bring heat from the cold side to the hot side. Thus, this can lower the temperature of the cold side.
The Peltier coefficient (Π) is related to the Seebeck coefficient by
(1.10)
In terms of this relationship, a material with a high Seebeck coefficient also has a high Peltier coefficient. Apart from the heat transfer by the Peltier effect, electrical current will generate Joule heat as well. Thus, the conductivity of the thermoelectric materials is also an important parameter for the Peltier cooling.
1.1.4 Thomson Effect
The Seebeck coefficient of materials is dependent on the temperature. A spatial gradient in temperature can generate a gradient in the Seebeck coefficient. When an electrical current flows through a material with temperature gradient, continuous Peltier effect can take place. This is called Thomson effect.
When a current density (J) transports through a homogeneous conductor, the heat generation rate per unit volume will be generated in terms of the Thomson effect,
(1.11)
where K Th is the Thomson coefficient and dT/dx is the temperature gradient. The Thomson coefficient is related to the Seebeck coefficient by,
(1.12)
1.1.5 Electrical Conductivity
In terms of the classic theory, the electrical conductivity of electronic materials depends on the charge carrier density (n) and charge carrier mobility (μ),
(1.13)
where e is the elementary charge of an electron.
1.1.5.1 Charge Carrier Density
Metals have high charge carrier density and thus high electrical conductivity. Their charge carrier density depends on the density and valence electrons of the metal atoms. Intrinsic semiconductors have very low charge carrier density, and charge carriers can be generated by temperature excitation or light‐induced excitation. The conductivity of a semiconductors can be increased by several orders of magnitude by doping. The electrical conductivity of a semiconductor depends on the electrons in the conduction band and holes in the valence band,
(1.14)
where