Figure 12.4 Collection area.
The procedure of semen collection is rather straightforward. Several bulls are usually penned separately along a “bull alley” facing the collection area. Mount animals are allowed to move along in front of the bulls in order to initiate some arousal. The bulls are allowed to observe other bulls mounting and being collected from this vantage point. It can be very evident that bulls in the bull gallery are aroused by the amount of vocalization that occurs as a bull is being collected.
Once it is time for a bull to be collected, he is allowed to leave his pen and enter the mount area. At this time, the mount handler will move the mount animal to prevent the bull from mounting. This may continue for several minutes until such a time as the semen collector is satisfied the bull is properly aroused. The semen collector may further determine that the bull needs to “false mount” to further his arousal and thus increase the quality and quantity of semen he produces. This is accomplished by the bull handler allowing the bull to mount but the semen handler diverting the penis away from the mount animal as the mount is withdrawn from under the bull. As discussed previously, when the semen collector believes the bull is properly stimulated, the bull is allowed to mount for collection (Figure 12.5). After collection the bull is either returned to housing or is placed back in the bull alley for another collection attempt.
Figure 12.5 Proper technique for collection of bull semen.
The preparation of the AV is important as the tactile sensation received by the bull is paramount to his semen production. It should simulate the natural breeding act as closely as possible. The AV is constricted, with a ridged tube that has a port allowing water to be added between the rigid structure and a latex liner. Within this liner another is placed to facilitate collection of the semen from the bull. This liner has a tapered end that allows the inclusion of a glass or plastic receptacle that will serve to hold the collected semen sample. Water added to the water jacket should be in the temperature range 40–60 °C and varies according to the preference of the bull; this has to be determined by the semen collector. Also, the amount of water within the jacket determines the rigidity of the liner, which can impact the bull's reaction to the AV. It is very important that a sterile non‐spermicidal lubricant be applied to the upper one‐third of the AV. This improves sensation and reduces the possibility of abrasive injury to the bull's penis.
For those bulls that are too fractious or are incapacitated and unable to jump a mount animal, the collector has the option to use an electroejaculator. Although it is discouraged in the semen production industry, it may be used when all else fails. Usually the bull will produce a slightly less concentrated ejaculate and with the potential for a somewhat higher abnormal sperm count. However, with proper stimulus (rectal massage of the ampulla and seminal vesicles) adequate semen may be collected for processing. Massage of the pelvic genitalia alone usually does not produce adequate semen product for processing and is discouraged in the industry.
Common Problems of Bulls at Stud
Lameness
Lameness is the most common problem in bulls at stud. The primary complaint from the stud manager will be lameness of acute onset. Some of the more common insults are hoof or foot rot, hairy heel wart (bovine dermatitis), hoof abscess, hoof lacerations, broken toes, and overgrown toes. Hoof abscesses due to wall separations (“white line disease”) are most often identified as the problem in these lame bulls. Most white line disease can be traced back to subclinical laminitis occurring some time in the bull's yearling development. The best curative approach is to access a hydraulic tilt table and to place the bull in lateral recumbency in order to remove the damaged sole and/or wall (Figures 12.6 and 12.7). Feed and water are withheld for 24 hours before table placement to reduce the chance of rumenal tympany while in lateral recumbency. If over 1 cm of sole or hoof wall is removed, it is recommended that an elevated block be placed on the opposing toe in order to reduce contact with the ground by the injured toe. Postprocedure antibiotics and analgesics are necessary to prevent infection and pain due to the lesion. Other injuries causing lameness are usually accidents that can occur in the collection areas, for example shoulder “sprains” when bulls get their forelimb hung up on the back of the mount animal and stifle injuries when mounting or dismounting the mount animal. Sometimes the only method available to properly diagnose the problem is diagnostic anesthesia, which often requires the use of a tilt table. Superficial injuries may be treated with a few days of non‐steroidal anti‐inflammatory drugs. The more serious may require more aggressive measures.
Figure 12.6 A well‐designed work area for performing lameness examinations at a custom stud. Note the hydraulic tilt table and footbath in foreground.
Figure 12.7 Assisting in preparation of hoof block application.
Treatment of issues such as foot rot or hairy heel wart may best be treated via footbath or topical therapy. The more stubborn infections may require antibiotics and periodic topical antibiotic bandages. If lameness persists after a few days of therapy, it is always recommended to question the original diagnosis and reinvestigate the problem.
Occasionally, a diffusely swollen limb is observed associated with a joint (most often a tarsus) with accompanying pyrexia, which can signal initiation of septic arthritis secondary to a generalized bacteremia. These are usually consequences of some kind of stress, most often change of feed or feeding methods. Any bull presenting with generalized cellulitis in a limb should be considered a medical emergency. Most bulls are not weight‐bearing and can be difficult to deal with in local settings, so it is often better to refer these cases to a facility capable of handling this kind of care.
Penile Injuries