Figure 1.6 Surface current distribution for (a) 780 MHz in lower frequency band and (b) 1880 MHz in upper frequency band.
The simulated (Figure 1.9a, c, e, g) and measured (Figure 1.9b, d, f, h) 3D radiation pattern for the lower reconfigurable bands for the selected 720, 770, 850, and 910 MHz is shown in Figure 1.9. Similarly, simulated (Figure 1.10a, c, e, g) and measured (Figure 1.10b, d, f, h) 3D radiation pattern for the higher consistent bands for the selected 1710, 1880, 2100, and 2600 MHz is shown in Figure 1.10. From these figures, it can be observed that the patterns are near omnidirectional except toward the higher frequency end, where patterns show slight multilobes and nulls. In all the cases, realized peak gain is positive and around 2 dBi for both simulated and measured cases. Further, the patterns toward the higher end show some directionality due to the ground plane effect which tends to push the radiated energy in a direction causing diversity that is helpful when the MIMO antenna system is implemented.
Figure 1.7 Comparison of the simulated (solid lines) and measured (dash lines) reflection coefficient magnitudes against specifications of the (a) lower 4G LTE frequency reconfigurable bands and (b) consistent higher frequency bands.
Figure 1.8 The simulated (solid lines) and measured (dash lines) total antenna efficiencies for (a) the reconfigurable states of the lower 4G bands and (b) the consistent higher frequency band.
Figure 1.9 Simulated (a, c, e, g) and measured (b, d, f, h) near‐omnidirectional 3D radiation pattern at (a, b) 720 MHz, (c, d) 770 MHz, (e, f) 850 MHz, and (g, h) 910 MHz.
Figure 1.10 Simulated (a, c, e, g) and measured (b, d, f, h) near‐omnidirectional 3D radiation pattern at (a, b) 1710 MHz, (c, d) 1880 MHz, (e, f) 2100 MHz, and (g, h) 2600 MHz.
1.7 Frequency Agile/Tunable Antenna
A frequency agile or tunable antenna can be realized by integrating tunable RF components such as varactor diodes or RF micro‐electro‐mechanical‐systems (MEMS) variable capacitors in an antenna structure. Like a reconfigurable antenna, such antennas also require necessary bias networks such as those implemented in [2] and shown in Figure 1.4a–c and hence is not repeated again. The antenna impedance and radiation mechanism depends on the variation in effective permittivity which in turn is related to the change in capacitance variation. Frequency (f) of an antenna can be described as follows:
(1.1)
where L and C are the inductance and capacitance of an antenna.
To demonstrate mechanism of such an antenna, an example is now discussed from [5]. The antenna utilizes a meandered planar portion on the right‐hand side, which includes a varactor diode and its biasing network and a rectangular‐shaped cutout portion on the left‐hand side on the central feed arm (Figure 1.11). The varactor capacitance variation alters the electrical length of the meandered portion of the antenna, which in turn varies the resonance frequency of the antenna. In addition to the tunable meandered portion of the antenna, the design also includes a rectangular‐shaped cutout geometry for realizing higher band. Thus, this antenna follows a two‐step design approach.
In the first design step, the meandered line was chosen as the location for placement of the varactor diode. Since the meandered line enables the antenna to resonate at the lower frequency band, adding a varactor to this section allows the antenna to become tunable. To provide a wider tunable band between 690 and 970 MHz, the meandered line's electrical length is essentially increased by adding the varactor diode (SMV1281). After optimizing the antenna with the varactor diode set in place, Figure 1.12 shows the meandered line length as ML = 137.5 mm, which is slightly below λ/2 at 970 MHz and the width of the meandered line is MW = 1.2 mm.
Figure 1.11 Antenna geometry with varactor diode and biasing network.
Source: Damman et al. [5].
Figure 1.12 Design parameters for the low (right) and high bands (left).
Source: Damman et al. [5].
The second design step requires adding a higher band antenna structure to the design such that, while the tuning of the lower band is obtained, the higher band is consistently present. The higher band antenna was chosen as a simple rectangular‐shaped structure with a rectangular‐shaped slot which was cutout within the middle of the structure (Figure 1.12). Adding this cutout improved the matching of the higher band and subsequently lowered the effect of frequency tuning in the higher band when the lower band was tuned. In such an antenna, current distributions on the two portions of the antenna should be as independent as possible, which is shown in Figure