If the amount of plant sample available is limited (i.e. roots), the option to make a stable pellet is unpractical and in this case the vegetation sample can be presented to the XRF spectrometer as a loose powder by packing it in a cell or by distributing the powder on an adhesive tape or X‐ray foil (made of polyester, polypropylene, polycarbonate, etc.). Using this latter approach, a plant layer ranging from 0.8–2.5 mg/cm2 can be obtained [32]. However, in view of the inherent X‐ray absorption by the foil, the sensitivity for low Z elements such as Na is reduced in comparison with the analysis of pressed pellets. Another shortcoming of loose powder preparation is the worse precision of the results obtained due to the bulk density and grain size differences between replicate measurements. In any case, depending on the analytical purpose, the loose powder preparation method can be a fast analytical alternative above all when the amount of sample is limited and WDXRF, 2D‐EDXRF, and 3D‐EDXRF systems are used.
Another interesting alternative when the amount of vegetation sample to be analyzed is scarce is the use of TXRF systems. As it was discussed in the previous section, to perform analysis by TXRF the sample should be presented as a thin film by deposition of a small amount of sample (a few μg or μl) on a reflective carrier. In terms of sample preparation procedure, an additional advantage of TXRF is the possibility to prepare easily the vegetation sample by suspending several milligrams of the powdered sample (10–50 mg) in an adequate disperser and depositing a few μl (5–20 μl) of the suspension on a reflective carrier. This approach has demonstrated to be effective, for example, in multi‐elemental analysis of vegetal foodstuff [24]. Nevertheless, it is interesting to remark that a careful study of all the parameters affecting suspension preparation and TXRF analysis (i.e. amount of sample, suspension concentration, dispersant type, sample deposition volume on the reflector, etc.) should be evaluated in order to obtain reliable results. Another important aspect to be considered to prepare homogeneous solid suspensions and to minimize the particle size agglomerations caused by the presence of particle superficial electrostatic forces when using suspension preparation, is to grind the sample to a particle size <100 μm and use high energy ultrasound treatments before sample deposition on the reflector. Finally, TXRF analysis is especially suited when calibration standards with a similar matrix to the analyzed samples are not available, since quantification can be performed by means of internal standardization. Using this approach, acceptable results in terms of accuracy and precision were obtained for the determination of mid‐high Z elements (Mn‐Sr) in vegetal foodstuff. But empirical calibration using several plant reference materials was necessary to correct absorption effects and obtain reliable results for low Z elements such as K and Ca.
Another more sophisticated sample treatment strategy to be used in combination with TXRF to improve limit of detection for trace elements in vegetation samples is digestion. Despite the fact that this approach implies longer analysis times and the consumption of reagents, the use of TXRF as a detection technique still entails lower costs than ICP based techniques as no consumables or cooling media are necessary in most of benchtop TXRF systems. Usually plant samples can be decomposed, as other biological matrices, using a mixture of nitric acid and hydrogen peroxide [33, 34]. However, as mentioned above, the silicon content in some plant species is quite high (up to 10%) and the use of hydrofluoric acid is needed to obtain a complete dissolution of the sample [3]. Classically, to perform the digestion procedure, digestions at atmospheric pressure using heat sources such as sand baths and hot plates are used. However, at present, microwave ovens are widely used as a faster alternative. Additional advantages of microwave digestions include the limiting of reagents consumption and also the decrease of analyte losses and sample contamination. Block heaters for digestion of small amounts of vegetation samples (several mg) have also been successfully employed [24]. Despite the fact that suspension and digestion are the most commonly used sample preparation strategies when analyzing vegetation samples by TXRF, other novel treatments have been recently developed. For instance, in a recent publication, tree leaves of different species were prepared by a novel device that first compressed the leaves between two 75 mm thick organic foils and then cut out a 30 mm diameter disc which was then stuck to a reflector and inserted into the TXRF system. Results were compared with those from microwave digestion and it was concluded that the non‐destructive direct method allowed rapid screening of leave samples with acceptable detection limits (0.5–18 mg/kg) [35].
Finally, the direct analysis of the plant material is necessary in some applications, above all when dealing with the study element distribution within plant tissues or in in vivo analysis. In this latter case, the specimen is directly analyzed by the XRF system and any sample treatment is not required. For example, the study of the intake of mineral nutrients by time‐resolved XRF analysis proved to be useful in the investigation of plant diseases due to nutrient deficiency and excess [36].
Usually, when performing μ‐XRF analysis to study element distribution within plant tissues a minimum sample treatment is necessary to ensure a flat and smooth surface of the vegetation sample which can affect the quality and reliability of μ‐XRF spectra collected. It has been demonstrated in different studies that dehydration of plant tissues can alter the in‐situ location of dissolved components [25]. For this reason, vegetation tissues are usually sandwiched between two thin films transparent to X‐rays to prevent the sample from drying, oxidizing and dehydrating [37]. More sophisticated sample treatments for μ‐XRF analysis include sectioning of the plant tissue. Different approaches are used for such purposes including the sectioning of the fresh tissue under cryogenic conditions or after embedding the tissue in a hard resin or soft paraffin wax. In the latter case, it is possible to obtain ultrathin (100 nm to 1 μm) sections that are very well‐suited for elemental distribution and speciation analysis of plant tissues using synchrotron radiation [38].
It is worth to mention that in p‐EDXRF systems vegetation samples can be measured in‐situ in the field without any sample treatment directly by pointing the handheld window (of approximately 2 cm2) to the vegetal tissue. Even under field‐moist conditions, it has been demonstrated, for instance, that p‐EDXRF systems can be reasonably used for the determination of Zn and Cu in different vegetation species [18]. However, a significant improvement of the results can be assessed if drying the vegetation sample or if using additional sample treatment such as the fabrication of pressed pellets from the powdered plant material [19].
2.4 Applications of XRF in the Field of Vegetation Samples Analysis
2.4.1 Environmental Studies
Due to the capacity of some vegetation species to accumulate metals from the growing media, they have been used as bioindicators in areas polluted with such contaminants. In this sense, XRF has been applied, for example, in some studies as an analytical technique for determining multi‐elemental composition of different vegetation species in areas affected by mining activities [3, 18, 39] or to study heavy metals in wild edible mushrooms under different pollution conditions [40]. In Figure 2.4, as an example, EDXRF spectra obtained in the analysis of leaves of Betula Pendula species sampled in a mining landfill and in a non‐polluted area are compared. As it can be seen, XRF spectra enable the discrimination between a sample growing on the mining waste landfill studied and the other one collected in a non‐polluted area (control sample) in a fast an easy way. Another interesting approach of multi‐elemental information derived from XRF analysis is the possibility to monitor other essential elements present in the vegetation sample that may change as a result of metal accumulation (i.e. K).