Figure 1.2 A vessel fabricated with a heavy wall to minimize cost
(Source: Los Alamos National Laboratory)
Figure 1.3 Side views of the vessel in Figure 1.2
The rolled and welded design proved to be the least costly. All of the heavy walled designs eliminated two circumferential welds at the ends, as well as the cost of layout and cutting of holes, and welding in the plates for the small openings. They also reduced the risk of distortion by minimizing the amount of welding required. The centrifugal cast and forged designs had higher costs for the basic cylinder than did the rolled and welded design.
When the user recognized the costs and the tolerance risks associated with welding a large number of nozzle plates, the rolled and welded design was accepted. The rolled and welded shell was produced by a pipe fabricating shop, helping to manage costs.
1.3.2.7 Process choices
Often decisions about cost of fabrication depend on the quantity of product being produced. Vessels will be more economical to produce if processes are optimized, but sometimes the cost of optimization is not warranted. For a single vessel, or even a small number of vessels, the cost of procuring forming equipment and optimal welding equipment and costs of developing tooling will likely exceed any profit on the job. Sometimes even setting up existing tooling for a vessel will not pay for itself, and it will be less expensive to fabricate the product using less efficient means but with essentially no initial setup cost.
1.3.2.8 Forming
Vessel fabricators will usually use one of four ways of making vessel shells.
First, as noted in Section 1.3.2.3.3, the least expensive way of producing a vessel shell is almost always to purchase a standard size of pipe, if it is available. This is usually true even for rolled and welded pipe.
Second, if large quantities are to be produced, is to develop dies and form shell sections using a large press. The cost of this tooling, even ignoring the cost of a press large enough to perform this type of work, is high, and it will only be justified by large quantities of product. For large quantities, however, this approach allows the production of shell sections (usually halves or thirds) with a single stroke of a press. Even the cost of installing the dies may be fairly high, and may not be cost effective for single vessels.
Third, rolled shell sections may be produced using forming rolls as described in Section 4.3, followed by placement of longitudinal welds. This technique is especially useful for diameters and shell lengths that can be rolled out of a single piece, since it efficiently produces cylinders requiring only a single longitudinal weld.
Finally, shells can be produced on a press brake. This is usually more labor intensive than either forming rolls or forming dies, but for small quantities of shell courses or if control of all aspects of the production is needed, it can make sense. For a company possessing a press brake but not forming rolls, rolling of pressure vessel shells can be accomplished in either of two ways: first, the shell can be “bump rolled” on the press, usually in sections, and second, the company can either buy the finished product or send shell material to a fabricator possessing a set of rolls for rolling. If the first approach is taken, the labor cost for bump‐rolling itself is probably greater than that for a product produced using forming rolls, but the cost of extra layout, pre‐crimping or cutting off extra material allowed in place of crimping (thicker sections), and shipping the product both directions are eliminated. Thus, for a single product, bump‐rolling may be adopted, while the second approach is likely if a number of shells are required and the roll setup costs can be better distributed over the number of shells produced.
If a very large quantity of the product is to be produced, particularly if it is to be produced on an ongoing basis, then a company may invest in a set of forming rolls. The cost of the rolls is then amortized over the life of the product line, costs go down, and the company has a new capability.
1.3.2.9 Fixturing
As in the case of tooling for rolling a shell course, the value of fixturing for fit‐up and assembly is often limited for production of a single or low volume product, but as production rises the cost of fixturing may remain constant while the benefits increase.
For a single shell, tack‐welded lugs, wedges, and clamps are often all that are needed and used for alignment, though in some cases hydraulic rams may be used. Lugs will be flame cut out of stock plate and welded in place – number of lugs, thickness of lugs, and amount of weld vary depending on how much “persuasion” the fit up is anticipated to require. After pushing shell edges (for example) into alignment so that they can be tacked together for welding, the wedges are removed, the lugs are ground free or knocked off, and any damage to the plate surface is repaired and ground flush.
Compare this scenario to the shop that has many shells of either the same size or a small number of predictable sizes to be produced. In this case, design and construction of fixtures to accomplish the same thing can cut individual shell fit‐up time significantly. Once shell fit‐up fixtures are constructed, the following might take place: The rolled plate section is placed on the fixture. Portions of the fixture will be swung into place and pinned. Hydraulic rams will push the sides and ends of the shell to bring the longitudinal joint into rough alignment. Other rams are used to bring the edges into the same plane. The side rams may be further adjusted to provide the proper root opening. The longitudinal seam is tacked, the rams are released, the fixture arms are moved back to provide space to remove the shell course, and the next shell is brought in.
There is often a sizable investment in a fixture such as this, and any such equipment that is developed will occupy shop space, so it shouldn’t be done without consideration of the returns. However, this investment can cut what may be an 8–16 (or even more) hour job to a matter of an hour or so.
1.3.2.10 Welding
A similar situation arises in the case of manual versus automated welding. A number of different processes may be used to produce welds. Each has its benefits and drawbacks. Chapter 7 discusses welding in detail and provides a comparison of various welding processes, including deposition rates. Items to consider include equipment and setup costs versus the benefits of more efficient placement of welds, design for production runs rather than individual fabrications, and weld configurations, such as narrow welds to minimize weld metal required and residual stresses.
1.3.2.11 Hydrotesting
Pressure testing is most often performed using water or other comparably incompressible fluids. Hydrotest of a single vessel is usually accomplished by filling it, pumping to pressure, holding, and draining the vessel. For single vessels, the water is usually dumped after use, and pumping is accomplished using a small positive displacement pump.
If the quantity of vessels produced in accordance with a particular vessel design is such that multiple vessels are tested daily, then it is common to set up test fixtures and to salvage and recycle the water. As with other means employed to reduce per unit cost, the savings must be weighed against the up‐front cost of fixturing, constructing